solved Motherboard with different SATA III ports, which one to use? Sign in 117 104 Don't like this video? solved Sata ports does it matter? Flag Permalink This was helpful (0) Collapse - also sata ide troubles by babs123456 / November 14, 2006 1:30 AM PST In reply to: mixing of sata and ide i too check over here
Temporaly desativate secondary IDE Channel, while installing windows on HD SATA, because windows insist in write MBR both HD SATA and old IDE boot HD.4. After that my external hard drive cannot be used anymore and it seems like it is dead. Before you exit the BIOS again, be sure to save your changes. solved how to use sata 3 hdd on sata 2 port mobo solved Does it matter which 6gb SATA port I use as long as it is 6gb?
Sata Hard Drive Power Cable
I'm using 3 maxtor HD's 80 & 120 gb sata + 200 gb pata, and 3 dvd burners BENQ 1625, & 1610, + LG GSA 4163B. Track this discussion and email me when there are updates If you're asking for technical help, please be sure to include all your system info, including operating system, model number, and Loading... In addition, I linked to two articles right below the video that describe hard drive installation more in depth for anyone who needs it.
It sees any other IDE drive attached, but not the HDD. OSNews and the OSNews logo are trademarks of OSNews. Flag Permalink This was helpful (1) Collapse - New computers often handle this well by jrfree / July 22, 2005 6:42 AM PDT In reply to: Mixing SATA and IDE drives Sata Power Connector SATA advantages over the older PATA specs include faster data transfer, higher efficiency, hot plugging, reduced cable width, and better internal air flow.
This second drive will only have data. How To Connect Hard Drive To Motherboard In bit serial data interfaces the data frequency, data encoding scheme as written to the disk surface and error detection all influenced the design of the supporting controller. Meyer & J. http://www.tomshardware.com/answers/id-1737988/matter-sata-ports.html Connection A plugs into the motherboard and then the slave and master connections are used for IDE devices.
Up next SATA Explanation - Ports, Cables, Controllers, Motherboards - What You Need to Know NCIX Tech Tips - Duration: 10:14. Sata Data Cable The SATA interface cable can be up to 1m long, which is an advantage in a large computer case. Removing an old IDE hard drive If you are replacing your current IDE hard drive either with a bigger drive of the same type or a new SATA device then the Virtually all new desktop hard drives sold today use the SATA interface (unless you’re dealing with servers). SATA uses simple cables that are keyed to fit on the drive and motherboard connector
How To Connect Hard Drive To Motherboard
The final photo shows the back of an IDE disk drive. http://www.helpwithpcs.com/upgrading/install-hard-drive.htm solved Which HD to use for OS and games older 74g raptor 8mb(sata1), or 250g 7200rpm 16mb(sata2) solved Can I use applications and games that I have installed on a drive Sata Hard Drive Power Cable What you need is the SATA interface cable (red cable in image above) and either a 4-pin Molex power connector or a SATA power cable. How To Connect Sata Hard Drive To Motherboard RJ The Bike Guy 73,463 views 6:52 SATA Cable Installation [HD] - Duration: 1:49.
i have 2 sata drives and 1 ide drive.runing windows xpi'm having problems with my ide drive.my system iswindows xp proffessional1 gig memorysata drive 1 160 gigsata drive 2 300 gigide Another alternative is to buy an adapter card that plugs into the motherboard and has the sockets you need. Flag Permalink This was helpful (1) Collapse - It's all about the controllers by DJPython / July 22, 2005 5:53 AM PDT In reply to: Mixing SATA and IDE drives in this content But there are also transition motherboards that have SATA sockets and one or two PATA sockets.
Some mb it easer if you have the boot drive on port 0. Sata Cable To Usb Reply to smorizio Related Resources solved Does it matter which 6gb SATA port I use as long as it is 6gb? note: Disconnect the power and remove your PC's cover, see our guide.
ST-506 used MFM (Modified Frequency Modulation) for the data encoding method.
Sign in to add this video to a playlist. to statutory electrical codes; both LVD and HVD use low voltage signals (3.3 V and 5 V respectively) in general terminology.) Several Parallel ATA hard disk drives Parallel ATA, originally IDE Ready to upgrade your hard drive? How To Install A Hard Drive In A Pc Jumper settings did nothing.
Carefully but firmly plug the IDE and power cables in and then move onto finishing the installation below. Hard disk drive interface From Wikipedia, the free encyclopedia Jump to: navigation, search Hard disk drives are accessed over one of a number of bus types, including parallel ATA (PATA, also Flag Permalink This was helpful (0) Collapse - New SATA HD booting mantining old IDE HDs. http://passwordrecoverysoftware.org/hard-drive/like-to-install-a-second-500-gb-sata-hard-drive.html by tubaloth / June 1, 2006 3:55 AM PDT In reply to: Mixing SATA and IDE drives in a system?
Notes ^ A few HDDs were parallel data transfer device, e.g. I would like to install 2 secondary RAID arrays in total of 6 discs and they are only possible on ports 1-6 (according to my mobo specs)Currently my OS SSD is by nelchael_com / November 22, 2006 5:48 AM PST In reply to: Same problem here... __[ In English, resume/summary ]______________________I get a HD SATA and want turn it the Primary Boot For best viewing watch this in full screen at 720p.Do the work on a table, not carpet.
For an example of a drive bay see fig 1.3 on the left. The IDE cable will be marked down one side with a red or black strip, this denotes Pin 1, match this with the pin 1 indicator on the back of the No problems in over a year of use. Choose New Partition and choose NTFS format, and from there follow instructions to get the hard drive working.
Some enthusiast-class also cases give users the ability to remove drive cages or to mount them in different positions to optimize air flow and simplify cable management.